MOBANetClocksV2-MIB DEFINITIONS ::= BEGIN -- Title: NTP Slave clock AGENT MIB -- SW-Nr.: 206457 -- Revision: 00 -- Date: 13.02.2015 -- Company: Moser-Baer AG, Switzerland -- By: Hansjörg Rohrer -- Version: 1.11 -- Changed: 17.09.2021 IMPORTS Integer32, OBJECT-TYPE, MODULE-IDENTITY, enterprises, Unsigned32, NOTIFICATION-TYPE, TimeTicks, IpAddress FROM SNMPv2-SMI OBJECT-GROUP, NOTIFICATION-GROUP, MODULE-COMPLIANCE FROM SNMPv2-CONF DisplayString, TEXTUAL-CONVENTION FROM SNMPv2-TC; mbnscMIB MODULE-IDENTITY LAST-UPDATED "202109171440Z" ORGANIZATION "Moser-Baer AG" CONTACT-INFO "Moser-Baer AG Spitalstr. 7 3454 Sumiswald support@mobatime.com" DESCRIPTION "This mib definition is used for all MOBATime network slave clocks which have IPv6 included." REVISION "202109171440Z" DESCRIPTION "add group mbnscNetWiFi" REVISION "201803221002Z" DESCRIPTION "initial version of this module" ::= { mobaNetClocks 100 } MOBAAlarm64 ::= TEXTUAL-CONVENTION DISPLAY-HINT "1x1x1x1x.1x1x1x1x" STATUS current DESCRIPTION "The alarm list is an array of bytes. The first byte defines the mask for the alarm bits 0..7. The last byte defines the mask for the alarm bits 56..63. Every byte has the range 0 ... 255 (binary)." SYNTAX OCTET STRING (SIZE(8)) MOBAFlags64 ::= TEXTUAL-CONVENTION DISPLAY-HINT "1x1x1x1x.1x1x1x1x" STATUS current DESCRIPTION "The flags are an array of bytes. The first byte defines the mask for the status bits 0..7. The last byte defines the mask for the status bits 56..63. Every byte has the range 0 ... 255 (binary)." SYNTAX OCTET STRING (SIZE(8)) MOBANetworkName ::= TEXTUAL-CONVENTION DISPLAY-HINT "255a" STATUS current DESCRIPTION "Fully qualified domain names or IP addresses in ASCII. IPv4 xxx.xxx.xxx.xxx IPV6 xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx name string max 40 chars" SYNTAX OCTET STRING (SIZE(1..40)) mobatime OBJECT IDENTIFIER ::= { enterprises 13842 } mobaNetClocks OBJECT IDENTIFIER ::= { mobatime 6 } mobaNetClocksV2 OBJECT IDENTIFIER ::= { mobaNetClocks 2 } mbnscNet OBJECT IDENTIFIER ::= { mobaNetClocksV2 1 } mbnscNetGen OBJECT IDENTIFIER ::= { mbnscNet 1 } mbnscNetGenMAC OBJECT-TYPE SYNTAX OCTET STRING (SIZE(6)) MAX-ACCESS read-only STATUS current DESCRIPTION "MAC-Address (xx xx xx xx xx xx)" ::= { mbnscNetGen 1 } mbnscNetGenIPMode OBJECT-TYPE SYNTAX INTEGER { both (0), ipv4only (1), ipv6only (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "IP Mode: 0: IPv4 and IPv6 1: IPv4 only 2: IPv6 only" ::= { mbnscNetGen 2 } mbnscNetGenIPNameserver OBJECT-TYPE SYNTAX DisplayString (SIZE(1..40)) MAX-ACCESS read-write STATUS current DESCRIPTION "IPv4 or IPv6 address (xxx.xxx.xxx.xxx or xxxx::xxxx:xxxx) of the nameserver" ::= { mbnscNetGen 3 } mbnscNetGenTZClientPort OBJECT-TYPE SYNTAX Unsigned32 (1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "Timezone client port. Default 65534" ::= { mbnscNetGen 4 } mbnscNetGenConfigPort OBJECT-TYPE SYNTAX Unsigned32 (1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "Configuration port. Default 65532" ::= { mbnscNetGen 5 } mbnscNetGenSnmpMode OBJECT-TYPE SYNTAX Unsigned32 (0..1) MAX-ACCESS read-only STATUS current DESCRIPTION "SNMP mode disabled 0: SNMP enabled (default) 1: SNMP disabled" ::= { mbnscNetGen 6 } mbnscNetGenMulticastMode OBJECT-TYPE SYNTAX Unsigned32 (0..1) MAX-ACCESS read-write STATUS current DESCRIPTION "Multicast mode disabled 0: Multicast enabled (default) 1: Multicast disabled" ::= { mbnscNetGen 7 } mbnscNetGenHostname OBJECT-TYPE SYNTAX DisplayString (SIZE(1..20)) MAX-ACCESS read-write STATUS current DESCRIPTION "Host name of the device" ::= { mbnscNetGen 8 } mbnscNetGenCommMode OBJECT-TYPE SYNTAX Unsigned32 (0..1) MAX-ACCESS read-only STATUS current DESCRIPTION "Communication / synchronisation mode 0=unicast 1=multicast (only for digital clocks)" ::= { mbnscNetGen 9 } mbnscNetGenMCastGrpIP OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "IP network address (xxx.xxx.xxx.xxx) of the multicast group IP e.g. 239.192.54.1 (only for digital clocks)" ::= { mbnscNetGen 10 } mbnscNetGenConfigCmd OBJECT-TYPE SYNTAX Unsigned32 (0..2) MAX-ACCESS read-write STATUS current DESCRIPTION "Network configuration changed command variable. 0: Not defined 1: SNMP has changed the configuration (possible restart of device) 2: SNMP requests to restore the old configuration" ::= { mbnscNetGen 100 } mbnscNetGenConfigChangedTime OBJECT-TYPE SYNTAX TimeTicks UNITS "Time ticks in 1/100th seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Time of the last configuration change." ::= { mbnscNetGen 101 } mbnscNetIPv4 OBJECT IDENTIFIER ::= { mbnscNet 2 } mbnscNetIPv4Addr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "IP network address (xxx.xxx.xxx.xxx) of the network slave clock" ::= { mbnscNetIPv4 1 } mbnscNetIPv4Mask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "IP subnet mask (xxx.xxx.xxx.xxx)" ::= { mbnscNetIPv4 2 } mbnscNetIPv4Gateway OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "IP network address (xxx.xxx.xxx.xxx) for the gateway" ::= { mbnscNetIPv4 3 } mbnscNetIPv4DHCPMode OBJECT-TYPE SYNTAX Unsigned32 (0..1) MAX-ACCESS read-write STATUS current DESCRIPTION "DHCP mode 0: DHCP disabled 1: DHCP enabled (default)" ::= { mbnscNetIPv4 4 } mbnscNetIPv4ConfigCmd OBJECT-TYPE SYNTAX Unsigned32 (0..2) MAX-ACCESS read-write STATUS current DESCRIPTION "Network configuration changed command variable. 0: Not defined 1: SNMP has changed the configuration (possible restart of device) 2: SNMP requests to restore the old configuration" ::= { mbnscNetIPv4 100 } mbnscNetIPv4ConfigChangedTime OBJECT-TYPE SYNTAX TimeTicks UNITS "Time ticks in 1/100th seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Time of the last configuration change." ::= { mbnscNetIPv4 101 } mbnscNetIPv6 OBJECT IDENTIFIER ::= { mbnscNet 3 } mbnscNetIPv6AddrLocal OBJECT-TYPE SYNTAX DisplayString (SIZE(1..40)) MAX-ACCESS read-only STATUS current DESCRIPTION "IP V6 link local network address (xxxx:xxxx::xxxx)" ::= { mbnscNetIPv6 1 } mbnscNetIPv6AddrAuto OBJECT-TYPE SYNTAX DisplayString (SIZE(1..40)) MAX-ACCESS read-only STATUS current DESCRIPTION "IP V6 network address by autoconfig (xxxx:xxxx::xxxx)" ::= { mbnscNetIPv6 2 } mbnscNetIPv6AddrDHCP OBJECT-TYPE SYNTAX DisplayString (SIZE(1..40)) MAX-ACCESS read-only STATUS current DESCRIPTION "IP V6 network address by DHCPv6 (xxxx:xxxx::xxxx)" ::= { mbnscNetIPv6 3 } mbnscNetIPv6AddrFix OBJECT-TYPE SYNTAX MOBANetworkName (SIZE(40)) MAX-ACCESS read-write STATUS current DESCRIPTION "IP V6 network address manual set (xxxx:xxxx::xxxx)" ::= { mbnscNetIPv6 4 } mbnscNetIPv6Prefix OBJECT-TYPE SYNTAX Unsigned32 (0..128) MAX-ACCESS read-write STATUS current DESCRIPTION "IPv6 subnet prefix for manual set IP address" ::= { mbnscNetIPv6 5 } mbnscNetIPv6Gateway OBJECT-TYPE SYNTAX DisplayString (SIZE(1..40)) MAX-ACCESS read-only STATUS current DESCRIPTION "IP V6 network address of gateway (next hop) (xxxx:xxxx::xxxx)" ::= { mbnscNetIPv6 6 } mbnscNetIPv6Config OBJECT-TYPE SYNTAX INTEGER { both (0), autoonly (1), dhcpv6only (2), none (3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Mode of IPv6 adress configuration 0: auto and fixed 1: autoconfig only 2: DHCPv6 only 3: none" ::= { mbnscNetIPv6 7 } mbnscNetIPv6ConfigCmd OBJECT-TYPE SYNTAX Unsigned32 (0..2) MAX-ACCESS read-write STATUS current DESCRIPTION "Network configuration changed command variable. 0: Not defined 1: SNMP has changed the configuration (possible restart of device) 2: SNMP requests to restore the old configuration" ::= { mbnscNetIPv6 100 } mbnscNetIPv6ConfigChangedTime OBJECT-TYPE SYNTAX TimeTicks UNITS "Time ticks in 1/100th seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Time of the last configuration change." ::= { mbnscNetIPv6 101 } mbnscNetWiFi OBJECT IDENTIFIER ::= { mbnscNet 4 } mbnscNetWiFiMode OBJECT-TYPE SYNTAX INTEGER { userSSID (1), predefinedSSID (2), accesPoint (3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Wifi mode defines how the module works: 1: wireless station with user SSID 2: wireless station with predefined SSID 3: Access point" ::= { mbnscNetWiFi 1 } mbnscNetWiFiSSID OBJECT-TYPE SYNTAX DisplayString (SIZE(1..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "SSID name of user wifi network. Default name is " ::= { mbnscNetWiFi 2 } mbnscNetWiFiSecurityType OBJECT-TYPE SYNTAX INTEGER { none (0), wpa (3), wpa2 (4), auto (5), leap (6), peap (7) } MAX-ACCESS read-write STATUS current DESCRIPTION "Security type of user wifi network: 0: none 1-2: reserved 3: wpa 4: wpa2 5: wpa/wpa2 = auto 6: leap 7: peap" ::= { mbnscNetWiFi 3 } mbnscNetWiFiPassword OBJECT-TYPE SYNTAX DisplayString (SIZE(1..64)) MAX-ACCESS read-write STATUS current DESCRIPTION "Password of user wifi network with security type WPA or EAP" ::= { mbnscNetWiFi 4 } mbnscNetWiFiEapUserName OBJECT-TYPE SYNTAX DisplayString (SIZE(1..64)) MAX-ACCESS read-write STATUS current DESCRIPTION "User name of wifi network with EAP security" ::= { mbnscNetWiFi 5 } mbnscNetWiFiEapDomain OBJECT-TYPE SYNTAX DisplayString (SIZE(1..64)) MAX-ACCESS read-write STATUS current DESCRIPTION "Domain of wifi network with EAP security" ::= { mbnscNetWiFi 6 } mbnscNetWiFiConfigCmd OBJECT-TYPE SYNTAX Unsigned32 (0..2) MAX-ACCESS read-write STATUS current DESCRIPTION "WiFi configuration changed command variable. 0: Not defined 1: SNMP has changed the configuration (possible restart of device) 2: SNMP requests to restore the old configuration" ::= { mbnscNetWiFi 100 } mbnscNetWiFiConfigChangedTime OBJECT-TYPE SYNTAX TimeTicks UNITS "Time ticks in 1/100th seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Time of the last configuration change." ::= { mbnscNetWiFi 101 } mbnscTime OBJECT IDENTIFIER ::= { mobaNetClocksV2 2 } mbnscTimeNTP1 OBJECT-TYPE SYNTAX DisplayString (SIZE(1..40)) MAX-ACCESS read-write STATUS current DESCRIPTION "String with IPv4 or IPv6 address (192.168.3.4 or FD03:2345:2345:2345::231) or DNS name to get NTP time information." ::= { mbnscTime 1 } mbnscTimeNTP2 OBJECT-TYPE SYNTAX DisplayString (SIZE(1..40)) MAX-ACCESS read-write STATUS current DESCRIPTION "String with IPv4 or IPv6 address (192.168.3.4 or FD03:2345:2345:2345::231) or DNS name to get NTP time information." ::= { mbnscTime 2 } mbnscTimeNTP3 OBJECT-TYPE SYNTAX DisplayString (SIZE(1..40)) MAX-ACCESS read-write STATUS current DESCRIPTION "String with IPv4 or IPv6 address (192.168.3.4 or FD03:2345:2345:2345::231) or DNS name to get NTP time information." ::= { mbnscTime 3 } mbnscTimeNTP4 OBJECT-TYPE SYNTAX DisplayString (SIZE(1..40)) MAX-ACCESS read-write STATUS current DESCRIPTION "String with IPv4 or IPv6 address (192.168.3.4 or FD03:2345:2345:2345::231) or DNS name to get NTP time information." ::= { mbnscTime 4 } mbnscTimeNTPcurrent OBJECT-TYPE SYNTAX DisplayString (SIZE(1..40)) MAX-ACCESS read-only STATUS current DESCRIPTION "IPv4 or IPv6 address of current NTP server" ::= { mbnscTime 5 } mbnscTimeNTPpollIntervall OBJECT-TYPE SYNTAX Unsigned32 (10..999) MAX-ACCESS read-write STATUS current DESCRIPTION "NTP request intervall 10..999sec" ::= { mbnscTime 6 } mbnscTimeDeviceTime OBJECT-TYPE SYNTAX Unsigned32 UNITS "Seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Actual device time (UTC). Seconds since 1.1.1970 00:00:00" ::= { mbnscTime 7 } mbnscTimeLocOffset OBJECT-TYPE SYNTAX Integer32 (-720..720) UNITS "minutes (min)" MAX-ACCESS read-only STATUS current DESCRIPTION "Offset to local time in minutes (-720..720)" ::= { mbnscTime 8 } mbnscTimeLastReception OBJECT-TYPE SYNTAX Unsigned32 UNITS "Seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Last received time (UTC). Seconds since 1.1.1970 00:00:00" ::= { mbnscTime 9 } mbnscTimeSyncTo OBJECT-TYPE SYNTAX Unsigned32 (1..255) UNITS "Hours (h)" MAX-ACCESS read-write STATUS current DESCRIPTION "Timeout after which no sync is indicated 1: after 1 hour of no sync 24: after 1 day of no sync (default) 168: after 7 days of no sync" ::= { mbnscTime 10 } mbnscTimeConfigCmd OBJECT-TYPE SYNTAX Unsigned32 (0..2) MAX-ACCESS read-write STATUS current DESCRIPTION "Time configuration changed command variable. 0: Not defined 1: SNMP has changed the configuration (possible restart of device) 2: SNMP requests to restore the old configuration" ::= { mbnscTime 100 } mbnscTimeConfigChangedTime OBJECT-TYPE SYNTAX TimeTicks UNITS "Time ticks in 1/100th seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Time of the last configuration change." ::= { mbnscTime 101 } mbnscTimeZone OBJECT IDENTIFIER ::= { mobaNetClocksV2 3 } mbnscTimeZoneVersion OBJECT-TYPE SYNTAX Integer32 (1..255) MAX-ACCESS read-only STATUS current DESCRIPTION "Actual version internal time zone table" ::= { mbnscTimeZone 1 } mbnscTimeZoneNumber OBJECT-TYPE SYNTAX Integer32 (0..255) MAX-ACCESS read-write STATUS current DESCRIPTION "Time zone 0: UTC 1..64: See user manual, time zone table 65..128: user defined time zone 129..143: time zone server 1..15 254: automatic time zone - e.g. UTC 255: internal user defined time zone (SET only used for digital clocks)" ::= { mbnscTimeZone 2 } mbnscTimeZoneEntry1 OBJECT-TYPE SYNTAX OCTET STRING (SIZE(18)) MAX-ACCESS read-only STATUS current DESCRIPTION "Time Zone entry -> see special definition" ::= { mbnscTimeZone 3 } mbnscTimeZoneEntry2 OBJECT-TYPE SYNTAX OCTET STRING (SIZE(18)) MAX-ACCESS read-only STATUS current DESCRIPTION "Time Zone entry -> see special definition" ::= { mbnscTimeZone 4 } mbnscTimeZoneEntry3 OBJECT-TYPE SYNTAX OCTET STRING (SIZE(18)) MAX-ACCESS read-only STATUS current DESCRIPTION "Time Zone entry -> see special definition" ::= { mbnscTimeZone 5 } mbnscTimeZoneEntry4 OBJECT-TYPE SYNTAX OCTET STRING (SIZE(18)) MAX-ACCESS read-only STATUS current DESCRIPTION "Time Zone entry -> see special definition" ::= { mbnscTimeZone 6 } mbnscTimeZoneEntry5 OBJECT-TYPE SYNTAX OCTET STRING (SIZE(18)) MAX-ACCESS read-only STATUS current DESCRIPTION "Time Zone entry -> see special definition" ::= { mbnscTimeZone 7 } mbnscTimeZoneEntry6 OBJECT-TYPE SYNTAX OCTET STRING (SIZE(18)) MAX-ACCESS read-only STATUS current DESCRIPTION "Time Zone entry -> see special definition" ::= { mbnscTimeZone 8 } mbnscTimeZoneEntry7 OBJECT-TYPE SYNTAX OCTET STRING (SIZE(18)) MAX-ACCESS read-only STATUS current DESCRIPTION "Time Zone entry -> see special definition" ::= { mbnscTimeZone 9 } mbnscTimeZoneConfigCmd OBJECT-TYPE SYNTAX Unsigned32 (0..2) MAX-ACCESS read-write STATUS current DESCRIPTION "Time zone configuration changed command variable. 0: Not defined 1: SNMP has changed the configuration (possible restart of device) 2: SNMP requests to restore the old configuration" ::= { mbnscTimeZone 100 } mbnscTimeZoneConfigChangedTime OBJECT-TYPE SYNTAX TimeTicks UNITS "Time ticks in 1/100th seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Time of the last configuration change." ::= { mbnscTimeZone 101 } mbnscMode OBJECT IDENTIFIER ::= { mobaNetClocksV2 4 } mbnscModeSwitchInfo OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Current switch settings (only analogue movements)" ::= { mbnscMode 1 } mbnscModeDisplayBrightness OBJECT-TYPE SYNTAX DisplayString (SIZE(0..2)) MAX-ACCESS read-write STATUS current DESCRIPTION "Display brightness for digital clocks 1..30, A (Auto)" ::= { mbnscMode 2 } mbnscModeDisplayFormat OBJECT-TYPE SYNTAX DisplayString (SIZE(0..2)) MAX-ACCESS read-write STATUS current DESCRIPTION "Display format 12h/24h for digital clocks" ::= { mbnscMode 3 } mbnscModeDisplayAlternate OBJECT-TYPE SYNTAX DisplayString (SIZE(0..2)) MAX-ACCESS read-write STATUS current DESCRIPTION "Display alternating mode for digital clocks 1: time continuously 2: date cont. 3: temperature cont. (sequence 6 sec. time, 3 sec. date for ECO-DC) 4: stopwatch cont. (only DC clock) 5: sequence 6 sec. time, 3 sec. date (only DC clock) 6: sequence 8 sec. time, 3 sec. date, 3 sec. temperature (only DC clock)" ::= { mbnscMode 4 } mbnscModeNTP OBJECT-TYPE SYNTAX DisplayString (SIZE(0..2)) MAX-ACCESS not-accessible STATUS obsolete DESCRIPTION "NTP synchronisation mode for digital clocks" ::= { mbnscMode 5 } mbnscModeIRlock OBJECT-TYPE SYNTAX DisplayString (SIZE(0..2)) MAX-ACCESS read-write STATUS current DESCRIPTION "IR autolock time for digital clocks (only DC clock) 1..60, U (autolock off)" ::= { mbnscMode 6 } mbnscModeTimeDispZeros OBJECT-TYPE SYNTAX DisplayString (SIZE(0..2)) MAX-ACCESS read-write STATUS current DESCRIPTION "Leading zeros time display for digital clocks (only DC clock) 1: time with leading zero 2: time without leading zero" ::= { mbnscMode 7 } mbnscModeDateDispZeros OBJECT-TYPE SYNTAX DisplayString (SIZE(0..2)) MAX-ACCESS read-write STATUS current DESCRIPTION "Leading zeros date display for digital clocks (only DC clock) 1: date with leading zero 2: date without leading zero" ::= { mbnscMode 8 } mbnscModeTempUnit OBJECT-TYPE SYNTAX DisplayString (SIZE(0..2)) MAX-ACCESS read-write STATUS current DESCRIPTION "Temperature unit for digital clocks (only DC clock) C: Celsius F: Fahrenheit" ::= { mbnscMode 9 } mbnscModeClockOpMode OBJECT-TYPE SYNTAX DisplayString (SIZE(0..2)) MAX-ACCESS read-write STATUS current DESCRIPTION "Operation mode for digital clocks (only DC clock) 0: normal mode 1: special mode 1 2: special mode 2" ::= { mbnscMode 10 } mbnscModeNWParam OBJECT-TYPE SYNTAX DisplayString (SIZE(0..2)) MAX-ACCESS not-accessible STATUS obsolete DESCRIPTION "Network parameter setting mode for digital clocks" ::= { mbnscMode 11 } mbnscModeDispDerating OBJECT-TYPE SYNTAX DisplayString (SIZE(0..2)) MAX-ACCESS read-write STATUS current DESCRIPTION "Display current deration setting for digital clocks (see service menu definition)" ::= { mbnscMode 12 } mbnscModeLightCorr OBJECT-TYPE SYNTAX DisplayString (SIZE(0..2)) MAX-ACCESS read-write STATUS current DESCRIPTION "Light measurement correction for digital clocks (see service menu definition)" ::= { mbnscMode 13 } mbnscModeConfigCmd OBJECT-TYPE SYNTAX Unsigned32 (0..2) MAX-ACCESS read-write STATUS current DESCRIPTION "Mode configuration changed command variable. 0: Not defined 1: SNMP has changed the configuration (possible restart of device) 2: SNMP requests to restore the old configuration" ::= { mbnscMode 100 } mbnscModeConfigChangedTime OBJECT-TYPE SYNTAX TimeTicks UNITS "Time ticks in 1/100th seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Time of the last configuration change." ::= { mbnscMode 101 } -- -- Group for additional digital clock modes -- mbnscAdditionalDigitalClockModes OBJECT IDENTIFIER ::= { mbnscMode 30 } -- -- Temperature Sensors "Sensors" -- mbnscSensors OBJECT IDENTIFIER ::= { mbnscAdditionalDigitalClockModes 1 } mbnscSensorsTempActivation OBJECT-TYPE SYNTAX DisplayString (SIZE(0..2)) MAX-ACCESS read-write STATUS current DESCRIPTION "Temperature sensor activation 1: DS18B20 3: TME (only sensor 1) 4: TME (Sensors 1 and 2)" ::= { mbnscSensors 1 } mbnscSensorsTemp1IPAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "IP network address (xxx.xxx.xxx.xxx) of the sensor 1 (SET only used for digital clocks)" ::= { mbnscSensors 2 } mbnscSensorsTemp2IPAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "IP network address (xxx.xxx.xxx.xxx) of the sensor 2 (SET only used for digital clocks)" ::= { mbnscSensors 3 } mbnscSensorsConfigCmd OBJECT-TYPE SYNTAX Unsigned32 (0..2) MAX-ACCESS read-write STATUS current DESCRIPTION "Mode configuration changed command variable. 0: Not defined 1: SNMP has changed the configuration (possible restart of device) 2: SNMP requests to restore the old configuration" ::= { mbnscSensors 100 } mbnscSensorsConfigChangedTime OBJECT-TYPE SYNTAX TimeTicks UNITS "Time ticks in 1/100th seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Time of the last configuration change." ::= { mbnscSensors 101 } -- -- Digital clock "DA" -- mbnscDA OBJECT IDENTIFIER ::= { mbnscAdditionalDigitalClockModes 2 } mbnscDASecondCircleDisplay OBJECT-TYPE SYNTAX DisplayString (SIZE(0..2)) MAX-ACCESS read-write STATUS current DESCRIPTION "The second circle display mode 1: Accumulating ring of seconds marker 2: Take actual second from full shining circle step by step 3: Full shining circle, actual second off 4: Three shining seconds, the first is showing actual second 5: Two shining seconds, the first is showing actual second" ::= { mbnscDA 1 } mbnscDAConfigCmd OBJECT-TYPE SYNTAX Unsigned32 (0..2) MAX-ACCESS read-write STATUS current DESCRIPTION "Mode configuration changed command variable. 0: Not defined 1: SNMP has changed the configuration (possible restart of device) 2: SNMP requests to restore the old configuration" ::= { mbnscDA 100 } mbnscDAConfigChangedTime OBJECT-TYPE SYNTAX TimeTicks UNITS "Time ticks in 1/100th seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Time of the last configuration change." ::= { mbnscDA 101 } -- -- Digital clock "DK" -- mbnscDK OBJECT IDENTIFIER ::= { mbnscAdditionalDigitalClockModes 3 } mbnscDKFirstLanguage OBJECT-TYPE SYNTAX DisplayString (SIZE(0..2)) MAX-ACCESS read-write STATUS current DESCRIPTION "First language selection 1: Czech 2: Slovak 3: English 4: German 5: ... (see manual for full language list)" ::= { mbnscDK 1 } mbnscDKSecondLanguage OBJECT-TYPE SYNTAX DisplayString (SIZE(0..2)) MAX-ACCESS read-write STATUS current DESCRIPTION "Second language selection 1: Czech 2: Slovak 3: English 4: German 5: ... (see manual for full language list)" ::= { mbnscDK 2 } mbnscDKThirdLanguage OBJECT-TYPE SYNTAX DisplayString (SIZE(0..2)) MAX-ACCESS read-write STATUS current DESCRIPTION "Third language selection 1: Czech 2: Slovak 3: English 4: German 5: ... (see manual for full language list)" ::= { mbnscDK 3 } mbnscDKTempUnitSecondLang OBJECT-TYPE SYNTAX DisplayString (SIZE(0..2)) MAX-ACCESS read-write STATUS current DESCRIPTION "Temperature units for second selected language C: Celsius F: Fahrenheit" ::= { mbnscDK 4 } mbnscDKTempUnitThirdLang OBJECT-TYPE SYNTAX DisplayString (SIZE(0..2)) MAX-ACCESS read-write STATUS current DESCRIPTION "Temperature units for third selected language C: Celsius F: Fahrenheit" ::= { mbnscDK 5 } mbnscDKAutoLangSwitchOver OBJECT-TYPE SYNTAX DisplayString (SIZE(0..2)) MAX-ACCESS read-write STATUS current DESCRIPTION "Language switch mode for automatic language switching over in one display alternating cycle A: all languages S: simple language" ::= { mbnscDK 6 } mbnscDKNumOfCharsForWeekday OBJECT-TYPE SYNTAX DisplayString (SIZE(0..2)) MAX-ACCESS read-write STATUS current DESCRIPTION "Number of characters used for weekday names 2: two characters 3: three characters" ::= { mbnscDK 7 } mbnscDKNamesFormatDisplay OBJECT-TYPE SYNTAX DisplayString (SIZE(0..2)) MAX-ACCESS read-write STATUS current DESCRIPTION "Weekday and month display format 1: first capital 2: all capitals" ::= { mbnscDK 8 } mbnscDKTemp1DescriptEnable OBJECT-TYPE SYNTAX DisplayString (SIZE(0..2)) MAX-ACCESS read-write STATUS current DESCRIPTION "Display of description for first measured temperature N/Y" ::= { mbnscDK 9 } mbnscDKTemp1Description OBJECT-TYPE SYNTAX DisplayString (SIZE(1..5)) MAX-ACCESS read-write STATUS current DESCRIPTION "Description text for first measured temperature" ::= { mbnscDK 10 } mbnscDKTemp2DescriptEnable OBJECT-TYPE SYNTAX DisplayString (SIZE(0..2)) MAX-ACCESS read-write STATUS current DESCRIPTION "Display of description for second measured temperature N/Y" ::= { mbnscDK 11 } mbnscDKTemp2Description OBJECT-TYPE SYNTAX DisplayString (SIZE(1..5)) MAX-ACCESS read-write STATUS current DESCRIPTION "Description text for second measured temperature" ::= { mbnscDK 12 } mbnscDKWorldTimeZone1 OBJECT-TYPE SYNTAX Integer32 (0..255) MAX-ACCESS read-write STATUS current DESCRIPTION "Index of time zone for world time zone 1 0: UTC 1..64: See user manual, time zone table 65..128: user defined time zone 129..143: time zone server 1..15 255: none (SET only used for digital clocks)" ::= { mbnscDK 13 } mbnscDKWorldTimeZone1Description OBJECT-TYPE SYNTAX DisplayString (SIZE(1..8)) MAX-ACCESS read-write STATUS current DESCRIPTION "Description text for World time zone 1" ::= { mbnscDK 14 } mbnscDKWorldTimeZone2 OBJECT-TYPE SYNTAX Integer32 (0..255) MAX-ACCESS read-write STATUS current DESCRIPTION "Index of time zone for world time zone 2 0: UTC 1..64: See user manual, time zone table 65..128: user defined time zone 129..143: time zone server 1..15 255: none (SET only used for digital clocks)" ::= { mbnscDK 15 } mbnscDKWorldTimeZone2Description OBJECT-TYPE SYNTAX DisplayString (SIZE(1..8)) MAX-ACCESS read-write STATUS current DESCRIPTION "Description text for World time zone 2" ::= { mbnscDK 16 } mbnscDKWorldTimeZone3 OBJECT-TYPE SYNTAX Integer32 (0..255) MAX-ACCESS read-write STATUS current DESCRIPTION "Index of time zone for world time zone 3 0: UTC 1..64: See user manual, time zone table 65..128: user defined time zone 129..143: time zone server 1..15 255: none (SET only used for digital clocks)" ::= { mbnscDK 17 } mbnscDKWorldTimeZone3Description OBJECT-TYPE SYNTAX DisplayString (SIZE(1..8)) MAX-ACCESS read-write STATUS current DESCRIPTION "Description text for World time zone 3" ::= { mbnscDK 18 } mbnscDKWorldTimeZone4 OBJECT-TYPE SYNTAX Integer32 (0..255) MAX-ACCESS read-write STATUS current DESCRIPTION "Index of time zone for world time zone 4 0: UTC 1..64: See user manual, time zone table 65..128: user defined time zone 129..143: time zone server 1..15 255: none (SET only used for digital clocks)" ::= { mbnscDK 19 } mbnscDKWorldTimeZone4Description OBJECT-TYPE SYNTAX DisplayString (SIZE(1..8)) MAX-ACCESS read-write STATUS current DESCRIPTION "Description text for World time zone 4" ::= { mbnscDK 20 } mbnscDKWorldTimeZone5 OBJECT-TYPE SYNTAX Integer32 (0..255) MAX-ACCESS read-write STATUS current DESCRIPTION "Index of time zone for world time zone 5 0: UTC 1..64: See user manual, time zone table 65..128: user defined time zone 129..143: time zone server 1..15 255: none (SET only used for digital clocks)" ::= { mbnscDK 21 } mbnscDKWorldTimeZone5Description OBJECT-TYPE SYNTAX DisplayString (SIZE(1..8)) MAX-ACCESS read-write STATUS current DESCRIPTION "Description text for World time zone 5" ::= { mbnscDK 22 } mbnscDKAutoTimeZoneSwitchOver OBJECT-TYPE SYNTAX DisplayString (SIZE(0..2)) MAX-ACCESS read-write STATUS current DESCRIPTION "World time switch mode for automatic time zone switching over in one display alternating cycle A: all world time zones S: simple world time zone" ::= { mbnscDK 23 } mbnscDKConfigCmd OBJECT-TYPE SYNTAX Unsigned32 (0..2) MAX-ACCESS read-write STATUS current DESCRIPTION "Mode configuration changed command variable. 0: Not defined 1: SNMP has changed the configuration (possible restart of device) 2: SNMP requests to restore the old configuration" ::= { mbnscDK 100 } mbnscDKConfigChangedTime OBJECT-TYPE SYNTAX TimeTicks UNITS "Time ticks in 1/100th seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Time of the last configuration change." ::= { mbnscDK 101 } -- -- Group for additional interface modes -- mbnscAdditionalInterfaceModes OBJECT IDENTIFIER ::= { mbnscMode 40 } -- -- Network-MOBALine-Interface "NMI" -- mbnscNMI OBJECT IDENTIFIER ::= { mbnscAdditionalInterfaceModes 1 } mbnscNMIDCFCurrentLoop OBJECT-TYPE SYNTAX INTEGER { off (0), on (1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Operation mode of the DCF77 current loop. 0: OFF 1: ON" ::= { mbnscNMI 1 } mbnscNMILineDriver OBJECT-TYPE SYNTAX INTEGER { off (0), mobaline (1), activdcf (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Operation mode of the line driver. 0: OFF 1: MOBALine 2: Active DCF" ::= { mbnscNMI 2 } mbnscNMIMOBALineMode OBJECT-TYPE SYNTAX INTEGER { normal (0), command12h (1), clockidcommand (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Operation mode of MOBALine. 0: normal operation 1: 12:00 mode, sideclocks shows 12:00 position 2: clock-id mode, sideclocks shows their ids if configured" ::= { mbnscNMI 3 } mbnscNMIMOBALineHandMode OBJECT-TYPE SYNTAX INTEGER { minstepsecstep (0), halfminstepsecstep (1), minconsecstep (2), minstepsecconwstop (256), halfminstepsecconwstop (257), minconsecconwstop (258), minstepseccon (512), halfminstepseccon (513), minconseccon (514), minstepseccwob (768), halfminstepseccwob (769), minconseccwob (770) } MAX-ACCESS read-write STATUS current DESCRIPTION "Minute hand mode operation of MOBALine. 0: minute step mode and second step mode 256: minute step mode and second continuous with stop mode 512: minute step mode and second continuous mode 768: minute step mode and second wobbling with stop 1: half minute step mode and second step mode 257: half minute step mode and second continuous with stop mode 513: half minute step mode and second continuous mode 769: half minute step mode and second wobbling with stop 2: continuous minute step mode and second step mode 258: continuous mode and second continuous with stop mode 514: continuous mode and second continuous mode 770: continuous mode and second wobbling with stop" ::= { mbnscNMI 4 } mbnscNMIActiveDCFMode OBJECT-TYPE SYNTAX INTEGER { mode1 (1), mode2 (2), mode3 (3), mode4 (4), mode5 (5), mode6 (6) } MAX-ACCESS read-write STATUS current DESCRIPTION "Operation mode of Active DCF. 1: Mode 1 2: Mode 2 3: Mode 3 4: Mode 4 5: Mode 5 6: Mode 6" ::= { mbnscNMI 5 } mbnscNMIConfigCmd OBJECT-TYPE SYNTAX Unsigned32 (0..2) MAX-ACCESS read-write STATUS current DESCRIPTION "General configuration changed command variable. 0: Not defined 1: SNMP has changed the configuration (possible restart of device) 2: SNMP requests to restore the old configuration" ::= { mbnscNMI 100 } mbnscNMIConfigChangedTime OBJECT-TYPE SYNTAX TimeTicks UNITS "Time ticks in 1/100th seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Time of the last configuration change." ::= { mbnscNMI 101 } -- -- Group for suprevised MOBALine sideclock states -- mbnscNMISideClockState OBJECT IDENTIFIER ::= { mbnscNMI 20 } mbnscNMISideClock1 OBJECT-TYPE SYNTAX INTEGER { notconfigured (0), clockok (3), clockerror (5) } MAX-ACCESS read-only STATUS current DESCRIPTION "State of side clock 1 0: Clock not configured 3: Clock OK 5: Clock error" ::= { mbnscNMISideClockState 1 } mbnscNMISideClock2 OBJECT-TYPE SYNTAX INTEGER { notconfigured (0), clockok (3), clockerror (5) } MAX-ACCESS read-only STATUS current DESCRIPTION "State of side clock 2 0: Clock not configured 3: Clock OK 5: Clock error" ::= { mbnscNMISideClockState 2 } mbnscNMISideClock3 OBJECT-TYPE SYNTAX INTEGER { notconfigured (0), clockok (3), clockerror (5) } MAX-ACCESS read-only STATUS current DESCRIPTION "State of side clock 3 0: Clock not configured 3: Clock OK 5: Clock error" ::= { mbnscNMISideClockState 3 } mbnscNMISideClock4 OBJECT-TYPE SYNTAX INTEGER { notconfigured (0), clockok (3), clockerror (5) } MAX-ACCESS read-only STATUS current DESCRIPTION "State of side clock 4 0: Clock not configured 3: Clock OK 5: Clock error" ::= { mbnscNMISideClockState 4 } mbnscNMISideClock5 OBJECT-TYPE SYNTAX INTEGER { notconfigured (0), clockok (3), clockerror (5) } MAX-ACCESS read-only STATUS current DESCRIPTION "State of side clock 5 0: Clock not configured 3: Clock OK 5: Clock error" ::= { mbnscNMISideClockState 5 } mbnscNMISideClock6 OBJECT-TYPE SYNTAX INTEGER { notconfigured (0), clockok (3), clockerror (5) } MAX-ACCESS read-only STATUS current DESCRIPTION "State of side clock 6 0: Clock not configured 3: Clock OK 5: Clock error" ::= { mbnscNMISideClockState 6 } mbnscNMISideClock7 OBJECT-TYPE SYNTAX INTEGER { notconfigured (0), clockok (3), clockerror (5) } MAX-ACCESS read-only STATUS current DESCRIPTION "State of side clock 7 0: Clock not configured 3: Clock OK 5: Clock error" ::= { mbnscNMISideClockState 7 } mbnscNMISideClock8 OBJECT-TYPE SYNTAX INTEGER { notconfigured (0), clockok (3), clockerror (5) } MAX-ACCESS read-only STATUS current DESCRIPTION "State of side clock 8 0: Clock not configured 3: Clock OK 5: Clock error" ::= { mbnscNMISideClockState 8 } mbnscNMISideClock9 OBJECT-TYPE SYNTAX INTEGER { notconfigured (0), clockok (3), clockerror (5) } MAX-ACCESS read-only STATUS current DESCRIPTION "State of side clock 9 0: Clock not configured 3: Clock OK 5: Clock error" ::= { mbnscNMISideClockState 9 } mbnscNMISideClock10 OBJECT-TYPE SYNTAX INTEGER { notconfigured (0), clockok (3), clockerror (5) } MAX-ACCESS read-only STATUS current DESCRIPTION "State of side clock 10 0: Clock not configured 3: Clock OK 5: Clock error" ::= { mbnscNMISideClockState 10 } mbnscNMISideClock11 OBJECT-TYPE SYNTAX INTEGER { notconfigured (0), clockok (3), clockerror (5) } MAX-ACCESS read-only STATUS current DESCRIPTION "State of side clock 11 0: Clock not configured 3: Clock OK 5: Clock error" ::= { mbnscNMISideClockState 11 } mbnscNMISideClock12 OBJECT-TYPE SYNTAX INTEGER { notconfigured (0), clockok (3), clockerror (5) } MAX-ACCESS read-only STATUS current DESCRIPTION "State of side clock 12 0: Clock not configured 3: Clock OK 5: Clock error" ::= { mbnscNMISideClockState 12 } -- -- Network-Clock Controller "NCC" -- mbnscNCC OBJECT IDENTIFIER ::= { mbnscAdditionalInterfaceModes 2 } mbnscNCCLightProperties OBJECT-TYPE SYNTAX INTEGER{ manuallylightoff (1), mains230vswitched (3), weekprogramoff (10), manuallylightonwrite (17), weekprogramon (42), manuallylightonread (49) } MAX-ACCESS read-write STATUS current DESCRIPTION "Light Mode and state. 1: manually light off 17: manually light on 49: manually light on 3: 230vswitched" ::= { mbnscNCC 1 } mbnscNCCLightBrightness OBJECT-TYPE SYNTAX INTEGER { dipswitch (0), current240mA (1), current350mA (3), current390mA (5), current500mA (7), current440mA (9), current550mA (11), current590mA (13), current700mA (15) } MAX-ACCESS read-write STATUS current DESCRIPTION "Light Brightness. 0: Read configuration of the DIP Switch 1: Light-current 240mA 3: Light-current 350mA 5: Light-current 390mA 9: Light-current 440mA 7: Light-current 500mA 11: Light-current 550mA 13: Light-current 590mA 15: Light-current 700mA" ::= { mbnscNCC 2 } mbnscNCCMOBALineHandMode OBJECT-TYPE SYNTAX INTEGER { minstepsecstep (0), halfminstepsecstep (1), minconsecstep (2), minstepsecconwstop (256), halfminstepsecconwstop (257), minconsecconwstop (258), minstepseccon (512), halfminstepseccon (513), minconseccon (514), minstepseccwob (768), halfminstepseccwob (769), minconseccwob (770) } MAX-ACCESS read-write STATUS current DESCRIPTION "Minute hand mode operation of MOBALine. 0: minute step mode and second step mode 256: minute step mode and second continuous with stop mode 512: minute step mode and second continuous mode 768: minute step mode and second wobbling with stop 1: half minute step mode and second step mode 257: half minute step mode and second continuous with stop mode 513: half minute step mode and second continuous mode 769: half minute step mode and second wobbling with stop 2: continuous minute step mode and second step mode 258: continuous mode and second continuous with stop mode 514: continuous mode and second continuous mode 770: continuous mode and second wobbling with stop" ::= { mbnscNCC 3 } mbnscNCCSideClock1 OBJECT-TYPE SYNTAX INTEGER { notconfigured0 (0), notconfigured2 (2), clockok (3), clockerror (5) } MAX-ACCESS read-only STATUS current DESCRIPTION "State of side clock 1 0: Clock not configured 2: Clock not configured 3: Clock OK 5: Clock error" ::= { mbnscNCC 4 } mbnscNCCSideClock2 OBJECT-TYPE SYNTAX INTEGER { notconfigured0 (0), notconfigured2 (2), clockok (3), clockerror (5) } MAX-ACCESS read-only STATUS current DESCRIPTION "State of side clock 2 0: Clock not configured 2: Clock not configured 3: Clock OK 5: Clock error" ::= { mbnscNCC 5 } mbnscNCCWeekprogID OBJECT-TYPE SYNTAX DisplayString (SIZE(8)) MAX-ACCESS read-only STATUS current DESCRIPTION "ID of the saved weekprogram" ::= { mbnscNCC 6 } mbnscNCCConfigCmd OBJECT-TYPE SYNTAX Unsigned32 (0..2) MAX-ACCESS read-write STATUS current DESCRIPTION "General configuration changed command variable. 0: Not defined 1: SNMP has changed the configuration (possible restart of device) 2: SNMP requests to restore the old configuration" ::= { mbnscNCC 100 } mbnscNCCConfigChangedTime OBJECT-TYPE SYNTAX TimeTicks UNITS "Time ticks in 1/100th seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Time of the last configuration change." ::= { mbnscNCC 101 } -- -- Network-Programmable Relay "NPR" -- mbnscNPR OBJECT IDENTIFIER ::= { mbnscAdditionalInterfaceModes 3 } mbnscNPRMode OBJECT-TYPE SYNTAX INTEGER{ weekprogram (0), remote (1) } MAX-ACCESS read-write STATUS current DESCRIPTION "NPR mode. 0: weekprogram 1: remote" ::= { mbnscNPR 1 } mbnscNPRWeekprogID OBJECT-TYPE SYNTAX DisplayString (SIZE(8)) MAX-ACCESS read-only STATUS current DESCRIPTION "ID of the saved weekprogram" ::= { mbnscNPR 2 } mbnscNPRRelayChannelStatus OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "NPR Relay status 1 Bit per channel 1 = on 0 = off" ::= { mbnscNPR 3 } mbnscNPRRelayChannelLockStatus OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "NPR Relay status 1 Bit per channel 1 = locked 0 = not locked" ::= { mbnscNPR 4 } mbnscNPRLockStatus OBJECT-TYPE SYNTAX INTEGER { notlocked (0), locked (1) } MAX-ACCESS read-only STATUS current DESCRIPTION "NPR Lock status 1 Bit per channel 0: not locked 1: locked" ::= { mbnscNPR 5 } mbnscNPRChannelNumbers OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of NPR channels" ::= { mbnscNPR 6 } mbnscNPRSwitchMode OBJECT-TYPE SYNTAX INTEGER { manuallyoff (0), manuallyon (1), auto (2) } MAX-ACCESS read-only STATUS current DESCRIPTION "NPR switch mode Manually OFF: 0 Manually On: 1 Auto: 2" ::= { mbnscNPR 7 } mbnscNPRConfigCmd OBJECT-TYPE SYNTAX Unsigned32 (0..2) MAX-ACCESS read-write STATUS current DESCRIPTION "General configuration changed command variable. 0: Not defined 1: SNMP has changed the configuration (possible restart of device) 2: SNMP requests to restore the old configuration" ::= { mbnscNPR 100 } mbnscNPRConfigChangedTime OBJECT-TYPE SYNTAX TimeTicks UNITS "Time ticks in 1/100th seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Time of the last configuration change." ::= { mbnscNPR 101 } mbnscGeneral OBJECT IDENTIFIER ::= { mobaNetClocksV2 5 } mbnscGeneralType OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Network slave clock type 1 Network Clock Interface NCI 2 Wireless Time Distribution WTD 868-T 3 NTP movement SEN 00 4 NTP movement NBU 190 5 Digital Clock ECO-DC 6 Digital Clock DC3 7 NTP movement SEN 40 8 NTP movement SAN 40 9 NTP digital clock DA 10 NTP calendar digital clock DK2 11 Network MOBALine Interface NMI 12 NTP clock TREND 13 NTP clock TREND double sided 14 NTP in- and outdoor digital clock DSC 15 NTP in- and outdoor digital clock DSC100 17 Network Clock Controller NCC 18 Network Programmable Relay NPR 19 Digital Clock ECO-M-DC 20 Digital clock TZI/TZO" ::= { mbnscGeneral 1 } mbnscGeneralName OBJECT-TYPE SYNTAX DisplayString (SIZE(0..20)) MAX-ACCESS read-write STATUS current DESCRIPTION "Device name (identifier)" ::= { mbnscGeneral 2 } mbnscGeneralFirmwareNumber OBJECT-TYPE SYNTAX DisplayString (SIZE(6)) MAX-ACCESS read-only STATUS current DESCRIPTION "Article number of the firmware." ::= { mbnscGeneral 3 } mbnscGeneralFirmwareVer OBJECT-TYPE SYNTAX DisplayString (SIZE(4)) MAX-ACCESS read-only STATUS current DESCRIPTION "Firmware version." REFERENCE "OFS_PROD_FIRMW_VER, 27, VARTYPE_STRING" ::= { mbnscGeneral 4 } mbnscGeneralStatus OBJECT-TYPE SYNTAX MOBAFlags64 MAX-ACCESS read-only STATUS current DESCRIPTION "Network slave clock status (64bit). Internal state of the network slave clock. Used for maintenance only. Bit 00 : time ok Bit 01 : 12h position Bit 02 : Reserved Bit 03 : Reserved Bit 04 : Reserved Bit 05 : Reserved Bit 06 : Reserved Bit 07 : Reserved Bit 08 : Reserved Bit 09 : Reserved Bit 10 : Reserved Bit 11 : Reserved Bit 12 : Reserved Bit 13 : Reserved Bit 14 : Reserved Bit 15 : Reserved Bit 16 : Reserved Bit 17 : Reserved Bit 18 : Reserved Bit 19 : Reserved Bit 20 : Reserved Bit 21 : Reserved Bit 22 : Reserved Bit 23 : Reserved Bit 24 : Reserved Bit 25 : Reserved Bit 26 : Reserved Bit 27 : Reserved Bit 28 : Reserved Bit 29 : Reserved Bit 30 : Reserved Bit 31 : Reserved Bit32..63 not used" ::= { mbnscGeneral 5 } mbnscGeneralAlarms OBJECT-TYPE SYNTAX MOBAAlarm64 MAX-ACCESS read-only STATUS current DESCRIPTION "Alarm state of the network slave clock Bit00=Synchronization Bit01=Power supply Bit02=Slave (cascade) Bit03=Illumination Bit04=Hands position (sec) Bit05=Hands position (m/h) Bit06=Restart Bit07=CommError Bit08=Time zone Bit09=Authentication error Bit10=Bootloader error Bit11=Reserved Bit12=Reserved Bit13=Reserved Bit14=Reserved Bit15=Reserved Bit16=Reserved Bit17=Reserved Bit18=Reserved Bit19=Reserved Bit20=Reserved Bit21=Reserved Bit22=Reserved Bit23=Reserved Bit24=Reserved Bit25=Reserved Bit26=Reserved Bit27=Reserved Bit28=Reserved Bit29=Reserved Bit30=Reserved Bit31=Reserved Bit32..Bit63=Device type specific error" ::= { mbnscGeneral 6 } mbnscGeneralSlaveInfo1 OBJECT-TYPE SYNTAX OCTET STRING (SIZE(26)) MAX-ACCESS read-only STATUS current DESCRIPTION "Info from slave 1 Byte 0..5 MAC Byte 6..11 Slave local time Byte 12..17 SW-number Byte 18..21 SW-version Byte 22 state Byte 23 reserved Byte 24 error Byte 25 reserved" ::= { mbnscGeneral 7 } mbnscGeneralSlaveInfo2 OBJECT-TYPE SYNTAX OCTET STRING (SIZE(26)) MAX-ACCESS read-only STATUS current DESCRIPTION "Info from slave 2 Byte 0..5 MAC Byte 6..11 Slave local time Byte 12..17 SW-number Byte 18..21 SW-version Byte 22 state Byte 23 reserved Byte 24 error Byte 25 reserved" ::= { mbnscGeneral 8 } mbnscGeneralSlaveInfo3 OBJECT-TYPE SYNTAX OCTET STRING (SIZE(26)) MAX-ACCESS read-only STATUS current DESCRIPTION "Info from slave 3 Byte 0..5 MAC Byte 6..11 Slave local time Byte 12..17 SW-number Byte 18..21 SW-version Byte 22 state Byte 23 reserved Byte 24 error Byte 25 reserved" ::= { mbnscGeneral 9 } mbnscGeneralBootloaderNumber OBJECT-TYPE SYNTAX DisplayString (SIZE(6)) MAX-ACCESS read-only STATUS current DESCRIPTION "Article number of the bootloader." ::= { mbnscGeneral 10 } mbnscGeneralBootloaderVer OBJECT-TYPE SYNTAX DisplayString (SIZE(4)) MAX-ACCESS read-only STATUS current DESCRIPTION "Bootloader version." ::= { mbnscGeneral 11 } mbnscGeneralConfigCmd OBJECT-TYPE SYNTAX Unsigned32 (0..2) MAX-ACCESS read-write STATUS current DESCRIPTION "General configuration changed command variable. 0: Not defined 1: SNMP has changed the configuration (possible restart of device) 2: SNMP requests to restore the old configuration" ::= { mbnscGeneral 100 } mbnscGeneralConfigChangedTime OBJECT-TYPE SYNTAX TimeTicks UNITS "Time ticks in 1/100th seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Time of the last configuration change." ::= { mbnscGeneral 101 } mbnscSupervision OBJECT IDENTIFIER ::= { mobaNetClocksV2 6 } mbnscSNMPManager1 OBJECT-TYPE SYNTAX DisplayString (SIZE(1..40)) MAX-ACCESS read-write STATUS current DESCRIPTION "String with IPv4 or IPv6 address (e.g 192.168.3.4 or FD03:2345:2345:2345::231) of the SNMP manager 1" ::= { mbnscSupervision 1 } mbnscSNMPManager2 OBJECT-TYPE SYNTAX DisplayString (SIZE(1..40)) MAX-ACCESS read-write STATUS current DESCRIPTION "String with IPv4 or IPv6 address (e.g 192.168.3.4 or FD03:2345:2345:2345::231) of the SNMP manager 2" ::= { mbnscSupervision 2 } mbnscSNMPTrapAliveMsgInterval OBJECT-TYPE SYNTAX Unsigned32 (0 | 1..1440) UNITS "minutes (min)" MAX-ACCESS read-write STATUS current DESCRIPTION "Time interval to send the alive message to the trap listener stations. 0: Alive message disabled >0: Alive message enabled Range: 1 ... 1440 minutes" ::= { mbnscSupervision 3 } mbnscSNMPConfigCmd OBJECT-TYPE SYNTAX Unsigned32 (0..2) MAX-ACCESS read-write STATUS current DESCRIPTION "SNMP / supervision services configuration changed command variable. 0: Not defined 1: SNMP has changed the configuration (possible restart of device) 2: SNMP requests to restore the old configuration" ::= { mbnscSupervision 100 } mbnscSNMPConfigChangedTime OBJECT-TYPE SYNTAX TimeTicks UNITS "Time ticks in 1/100th seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Time of the last configuration change." ::= { mbnscSupervision 101 } mbnscCommand OBJECT IDENTIFIER ::= { mobaNetClocksV2 7 } mbnscCommand12Pos OBJECT-TYPE SYNTAX Unsigned32 (0..1) MAX-ACCESS read-write STATUS current DESCRIPTION "Mode of the analogue clock: 0=run, 1=12h position" ::= { mbnscCommand 1 } mbnscCommandSWReset OBJECT-TYPE SYNTAX Unsigned32 (0..1) MAX-ACCESS read-write STATUS current DESCRIPTION "Command SW reset if set to 1" ::= { mbnscCommand 2 } mbnscCommandFactorySetting OBJECT-TYPE SYNTAX Unsigned32 (0..1) MAX-ACCESS read-write STATUS current DESCRIPTION "Restore factory settings if set to 1" ::= { mbnscCommand 3 } mbnscCommandFirmwUpd OBJECT-TYPE SYNTAX OCTET STRING (SIZE(10)) MAX-ACCESS read-write STATUS current DESCRIPTION "Command to start FW update, configure filename. TFTP server needs to be on this same device as the SNMP manager" ::= { mbnscCommand 4 } mbnscCommandExtContact OBJECT-TYPE SYNTAX Integer32 (0..1) MAX-ACCESS read-only STATUS current DESCRIPTION "Set external contact" ::= { mbnscCommand 5 } mbnscCommandConfigCmd OBJECT-TYPE SYNTAX Unsigned32 (0..2) MAX-ACCESS read-write STATUS current DESCRIPTION "SNMP / supervision services configuration changed command variable. 0: Not defined 1: SNMP has changed the configuration (possible restart of device) 2: SNMP requests to restore the old configuration" ::= { mbnscCommand 100 } mbnscSnmpConfig OBJECT IDENTIFIER ::= { mobaNetClocksV2 9 } mbnscSnmpCurrentAlarmInfo OBJECT IDENTIFIER ::= { mbnscSnmpConfig 1 } mbnscTrapAlMsgErrorNr OBJECT-TYPE SYNTAX Integer32 (0..63) MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "Error number of the trap message." ::= { mbnscSnmpCurrentAlarmInfo 1 } mbnscTrapAlMsgErrorState OBJECT-TYPE SYNTAX Integer32 (0..1) MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "Error state of the trap message." ::= { mbnscSnmpCurrentAlarmInfo 2 } mbnscTrapAlMsgErrorTime OBJECT-TYPE SYNTAX Integer32 UNITS "Seconds" MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "Error time of the trap message. Seconds since 1.1.1970 00:00:00" ::= { mbnscSnmpCurrentAlarmInfo 3 } mbnscTraps OBJECT IDENTIFIER ::= { mobaNetClocksV2 10 } mbnscTrapsAlarm NOTIFICATION-TYPE OBJECTS { mbnscTrapAlMsgErrorNr, mbnscTrapAlMsgErrorState, mbnscTrapAlMsgErrorTime } STATUS current DESCRIPTION "Alarm trap with attached (binded variables) alarm information: mbnscTrapAlMsgErrorNr, mbnscTrapAlMsgErrorState, mbnscTrapAlMsgErrorTime" ::= { mbnscTraps 1 } mbnscTrapsAlive NOTIFICATION-TYPE OBJECTS { mbnscGeneralStatus, mbnscGeneralAlarms } STATUS current DESCRIPTION "Device alive trap. Will be send in the configured interval. Attached are the variables mbnscGeneralStatus and mbnscGeneralAlarms." ::= { mbnscTraps 2 } mbnscMIBCompliance OBJECT IDENTIFIER ::= { mbnscMIB 1 } mbnscMIBCompliances MODULE-COMPLIANCE STATUS current DESCRIPTION "Please replace this text with your description." MODULE -- this module GROUP mbnscGrpNBU190 DESCRIPTION "Parameters for NBU 190 movement" GROUP mbnscGrpSEN40 DESCRIPTION "Parameters for SEN 40 movement" GROUP mbnscGrpDC DESCRIPTION "Parameters for DC digital clock" GROUP mbnscGrpECODC DESCRIPTION "Parameters for ECO DC digital clock" GROUP mbnscGrpDA DESCRIPTION "Parameters for DA digital clock" GROUP mbnscGrpDK DESCRIPTION "Parameters for DK digital clock" GROUP mbnscGrpNMI DESCRIPTION "Parameters for Network-MOBALine-Interface NMI" GROUP mbnscGrpNCC DESCRIPTION "Parameters for NCC network clock controller" GROUP mbnscGrpNPR DESCRIPTION "Parameters for NPR network programming relay" GROUP mbnscGrpTREND DESCRIPTION "Parameters for TREND movement" GROUP mbnscGrpNotUsedParameters DESCRIPTION "Parameters not yet used in any other group" ::= { mbnscMIBCompliance 1 } mbnscMIBGroups OBJECT IDENTIFIER ::= { mbnscMIB 2 } mbnscAllNotifications NOTIFICATION-GROUP NOTIFICATIONS { mbnscTrapsAlarm, mbnscTrapsAlive } STATUS current DESCRIPTION "This automatically created notification group contains all notifications that do not belong to any other NOTIFICATION-GROUP" ::= { mbnscMIBGroups 1 } mbnscGrpNBU190 OBJECT-GROUP OBJECTS { mbnscNetGenMAC, mbnscNetGenIPMode, mbnscNetGenIPNameserver, mbnscNetGenTZClientPort, mbnscNetGenConfigPort, mbnscNetGenSnmpMode, mbnscNetGenMulticastMode, mbnscNetGenHostname, mbnscNetGenCommMode, mbnscNetGenMCastGrpIP, mbnscNetGenConfigCmd, mbnscNetGenConfigChangedTime, mbnscNetIPv4Addr, mbnscNetIPv4Mask, mbnscNetIPv4Gateway, mbnscNetIPv4DHCPMode, mbnscNetIPv4ConfigCmd, mbnscNetIPv4ConfigChangedTime, mbnscNetIPv6AddrLocal, mbnscNetIPv6AddrAuto, mbnscNetIPv6AddrDHCP, mbnscNetIPv6AddrFix, mbnscNetIPv6Prefix, mbnscNetIPv6Gateway, mbnscNetIPv6Config, mbnscNetIPv6ConfigCmd, mbnscNetIPv6ConfigChangedTime, mbnscTimeNTP1, mbnscTimeNTP2, mbnscTimeNTP3, mbnscTimeNTP4, mbnscTimeNTPcurrent, mbnscTimeNTPpollIntervall, mbnscTimeDeviceTime, mbnscTimeLocOffset, mbnscTimeLastReception, mbnscTimeSyncTo, mbnscTimeConfigCmd, mbnscTimeConfigChangedTime, mbnscTimeZoneVersion, mbnscTimeZoneNumber, mbnscTimeZoneConfigCmd, mbnscTimeZoneConfigChangedTime, mbnscModeConfigCmd, mbnscModeConfigChangedTime, mbnscGeneralType, mbnscGeneralName, mbnscGeneralFirmwareNumber, mbnscGeneralFirmwareVer, mbnscGeneralStatus, mbnscGeneralAlarms, mbnscGeneralSlaveInfo1, mbnscGeneralSlaveInfo2, mbnscGeneralSlaveInfo3, mbnscGeneralConfigCmd, mbnscGeneralConfigChangedTime, mbnscSNMPManager1, mbnscSNMPManager2, mbnscSNMPTrapAliveMsgInterval, mbnscSNMPConfigCmd, mbnscSNMPConfigChangedTime, mbnscCommand12Pos, mbnscCommandSWReset, mbnscCommandConfigCmd, mbnscTrapAlMsgErrorNr, mbnscTrapAlMsgErrorState, mbnscTrapAlMsgErrorTime } STATUS current DESCRIPTION "All parameters used for NBU 190 movement" ::= { mbnscMIBGroups 2 } mbnscGrpSEN40 OBJECT-GROUP OBJECTS { mbnscNetGenMAC, mbnscNetGenIPMode, mbnscNetGenIPNameserver, mbnscNetGenTZClientPort, mbnscNetGenConfigPort, mbnscNetGenSnmpMode, mbnscNetGenMulticastMode, mbnscNetGenHostname, mbnscNetGenCommMode, mbnscNetGenMCastGrpIP, mbnscNetGenConfigCmd, mbnscNetGenConfigChangedTime, mbnscNetIPv4Addr, mbnscNetIPv4Mask, mbnscNetIPv4Gateway, mbnscNetIPv4DHCPMode, mbnscNetIPv4ConfigCmd, mbnscNetIPv4ConfigChangedTime, mbnscNetIPv6AddrLocal, mbnscNetIPv6AddrAuto, mbnscNetIPv6AddrDHCP, mbnscNetIPv6AddrFix, mbnscNetIPv6Prefix, mbnscNetIPv6Gateway, mbnscNetIPv6Config, mbnscNetIPv6ConfigCmd, mbnscNetIPv6ConfigChangedTime, mbnscTimeNTP1, mbnscTimeNTP2, mbnscTimeNTP3, mbnscTimeNTP4, mbnscTimeNTPcurrent, mbnscTimeNTPpollIntervall, mbnscTimeDeviceTime, mbnscTimeLocOffset, mbnscTimeLastReception, mbnscTimeSyncTo, mbnscTimeConfigCmd, mbnscTimeConfigChangedTime, mbnscTimeZoneVersion, mbnscTimeZoneNumber, mbnscTimeZoneConfigCmd, mbnscTimeZoneConfigChangedTime, mbnscModeConfigCmd, mbnscModeConfigChangedTime, mbnscGeneralType, mbnscGeneralName, mbnscGeneralFirmwareNumber, mbnscGeneralFirmwareVer, mbnscGeneralStatus, mbnscGeneralAlarms, mbnscGeneralSlaveInfo1, mbnscGeneralConfigCmd, mbnscGeneralConfigChangedTime, mbnscSNMPManager1, mbnscSNMPManager2, mbnscSNMPTrapAliveMsgInterval, mbnscSNMPConfigCmd, mbnscSNMPConfigChangedTime, mbnscCommand12Pos, mbnscCommandSWReset, mbnscCommandConfigCmd, mbnscTrapAlMsgErrorNr, mbnscTrapAlMsgErrorState, mbnscTrapAlMsgErrorTime } STATUS current DESCRIPTION "All parameters used for SEN 40 movement" ::= { mbnscMIBGroups 3 } mbnscGrpDC OBJECT-GROUP OBJECTS { mbnscNetGenMAC, mbnscNetGenIPMode, mbnscNetGenIPNameserver, mbnscNetGenTZClientPort, mbnscNetGenConfigPort, mbnscNetGenSnmpMode, mbnscNetGenMulticastMode, mbnscNetGenHostname, mbnscNetGenCommMode, mbnscNetGenMCastGrpIP, mbnscNetGenConfigCmd, mbnscNetGenConfigChangedTime, mbnscNetIPv4Addr, mbnscNetIPv4Mask, mbnscNetIPv4Gateway, mbnscNetIPv4DHCPMode, mbnscNetIPv4ConfigCmd, mbnscNetIPv4ConfigChangedTime, mbnscNetIPv6AddrLocal, mbnscNetIPv6AddrAuto, mbnscNetIPv6AddrDHCP, mbnscNetIPv6AddrFix, mbnscNetIPv6Prefix, mbnscNetIPv6Gateway, mbnscNetIPv6Config, mbnscNetIPv6ConfigCmd, mbnscNetIPv6ConfigChangedTime, mbnscNetWiFiMode, mbnscNetWiFiSSID, mbnscNetWiFiSecurityType, mbnscNetWiFiPassword, mbnscNetWiFiEapUserName, mbnscNetWiFiEapDomain, mbnscNetWiFiConfigCmd, mbnscNetWiFiConfigChangedTime, mbnscTimeNTP1, mbnscTimeNTP2, mbnscTimeNTP3, mbnscTimeNTP4, mbnscTimeNTPcurrent, mbnscTimeNTPpollIntervall, mbnscTimeDeviceTime, mbnscTimeLocOffset, mbnscTimeLastReception, mbnscTimeSyncTo, mbnscTimeConfigCmd, mbnscTimeConfigChangedTime, mbnscTimeZoneVersion, mbnscTimeZoneNumber, mbnscTimeZoneConfigCmd, mbnscTimeZoneConfigChangedTime, mbnscModeDisplayBrightness, mbnscModeDisplayFormat, mbnscModeDisplayAlternate, mbnscModeIRlock, mbnscModeTimeDispZeros, mbnscModeDateDispZeros, mbnscModeTempUnit, mbnscModeClockOpMode, mbnscModeDispDerating, mbnscModeLightCorr, mbnscModeConfigCmd, mbnscModeConfigChangedTime, mbnscSensorsTempActivation, mbnscSensorsTemp1IPAddr, mbnscSensorsTemp2IPAddr, mbnscSensorsConfigCmd, mbnscSensorsConfigChangedTime, mbnscGeneralType, mbnscGeneralName, mbnscGeneralFirmwareNumber, mbnscGeneralFirmwareVer, mbnscGeneralStatus, mbnscGeneralAlarms, mbnscGeneralBootloaderNumber, mbnscGeneralBootloaderVer, mbnscGeneralConfigCmd, mbnscGeneralConfigChangedTime, mbnscSNMPManager1, mbnscSNMPManager2, mbnscSNMPTrapAliveMsgInterval, mbnscSNMPConfigCmd, mbnscSNMPConfigChangedTime, mbnscCommandSWReset, mbnscCommandFactorySetting, mbnscCommandFirmwUpd, mbnscCommandConfigCmd, mbnscTrapAlMsgErrorNr, mbnscTrapAlMsgErrorState, mbnscTrapAlMsgErrorTime } STATUS current DESCRIPTION "All parameters used for DC digital clock" ::= { mbnscMIBGroups 4 } mbnscGrpECODC OBJECT-GROUP OBJECTS { mbnscNetGenMAC, mbnscNetGenIPMode, mbnscNetGenIPNameserver, mbnscNetGenTZClientPort, mbnscNetGenConfigPort, mbnscNetGenSnmpMode, mbnscNetGenMulticastMode, mbnscNetGenHostname, mbnscNetGenCommMode, mbnscNetGenMCastGrpIP, mbnscNetGenConfigCmd, mbnscNetGenConfigChangedTime, mbnscNetIPv4Addr, mbnscNetIPv4Mask, mbnscNetIPv4Gateway, mbnscNetIPv4DHCPMode, mbnscNetIPv4ConfigCmd, mbnscNetIPv4ConfigChangedTime, mbnscNetIPv6AddrLocal, mbnscNetIPv6AddrAuto, mbnscNetIPv6AddrDHCP, mbnscNetIPv6AddrFix, mbnscNetIPv6Prefix, mbnscNetIPv6Gateway, mbnscNetIPv6Config, mbnscNetIPv6ConfigCmd, mbnscNetIPv6ConfigChangedTime, mbnscNetWiFiMode, mbnscNetWiFiSSID, mbnscNetWiFiSecurityType, mbnscNetWiFiPassword, mbnscNetWiFiEapUserName, mbnscNetWiFiEapDomain, mbnscNetWiFiConfigCmd, mbnscNetWiFiConfigChangedTime, mbnscTimeNTP1, mbnscTimeNTP2, mbnscTimeNTP3, mbnscTimeNTP4, mbnscTimeNTPcurrent, mbnscTimeNTPpollIntervall, mbnscTimeDeviceTime, mbnscTimeLocOffset, mbnscTimeLastReception, mbnscTimeConfigCmd, mbnscTimeConfigChangedTime, mbnscTimeZoneVersion, mbnscTimeZoneNumber, mbnscTimeZoneConfigCmd, mbnscTimeZoneConfigChangedTime, mbnscModeDisplayBrightness, mbnscModeDisplayFormat, mbnscModeDisplayAlternate, mbnscModeDispDerating, mbnscModeLightCorr, mbnscModeConfigCmd, mbnscModeConfigChangedTime, mbnscGeneralType, mbnscGeneralName, mbnscGeneralFirmwareNumber, mbnscGeneralFirmwareVer, mbnscGeneralStatus, mbnscGeneralAlarms, mbnscGeneralBootloaderNumber, mbnscGeneralBootloaderVer, mbnscGeneralConfigCmd, mbnscGeneralConfigChangedTime, mbnscSNMPManager1, mbnscSNMPManager2, mbnscSNMPTrapAliveMsgInterval, mbnscSNMPConfigCmd, mbnscSNMPConfigChangedTime, mbnscCommandSWReset, mbnscCommandFactorySetting, mbnscCommandFirmwUpd, mbnscCommandConfigCmd, mbnscTrapAlMsgErrorNr, mbnscTrapAlMsgErrorState, mbnscTrapAlMsgErrorTime } STATUS current DESCRIPTION "All parameters used for ECO DC digital clock" ::= { mbnscMIBGroups 5 } mbnscGrpDA OBJECT-GROUP OBJECTS { mbnscNetGenMAC, mbnscNetGenIPMode, mbnscNetGenIPNameserver, mbnscNetGenTZClientPort, mbnscNetGenConfigPort, mbnscNetGenSnmpMode, mbnscNetGenMulticastMode, mbnscNetGenHostname, mbnscNetGenCommMode, mbnscNetGenMCastGrpIP, mbnscNetGenConfigCmd, mbnscNetGenConfigChangedTime, mbnscNetIPv4Addr, mbnscNetIPv4Mask, mbnscNetIPv4Gateway, mbnscNetIPv4DHCPMode, mbnscNetIPv4ConfigCmd, mbnscNetIPv4ConfigChangedTime, mbnscNetIPv6AddrLocal, mbnscNetIPv6AddrAuto, mbnscNetIPv6AddrDHCP, mbnscNetIPv6AddrFix, mbnscNetIPv6Prefix, mbnscNetIPv6Gateway, mbnscNetIPv6Config, mbnscNetIPv6ConfigCmd, mbnscNetIPv6ConfigChangedTime, mbnscNetWiFiMode, mbnscNetWiFiSSID, mbnscNetWiFiSecurityType, mbnscNetWiFiPassword, mbnscNetWiFiEapUserName, mbnscNetWiFiEapDomain, mbnscNetWiFiConfigCmd, mbnscNetWiFiConfigChangedTime, mbnscTimeNTP1, mbnscTimeNTP2, mbnscTimeNTP3, mbnscTimeNTP4, mbnscTimeNTPcurrent, mbnscTimeNTPpollIntervall, mbnscTimeDeviceTime, mbnscTimeLocOffset, mbnscTimeLastReception, mbnscTimeConfigCmd, mbnscTimeConfigChangedTime, mbnscTimeZoneVersion, mbnscTimeZoneNumber, mbnscTimeZoneConfigCmd, mbnscTimeZoneConfigChangedTime, mbnscModeDisplayBrightness, mbnscModeDisplayFormat, mbnscModeDisplayAlternate, mbnscModeIRlock, mbnscModeTimeDispZeros, mbnscModeDateDispZeros, mbnscModeTempUnit, mbnscModeClockOpMode, mbnscModeDispDerating, mbnscModeLightCorr, mbnscModeConfigCmd, mbnscModeConfigChangedTime, mbnscSensorsTempActivation, mbnscSensorsTemp1IPAddr, mbnscSensorsTemp2IPAddr, mbnscSensorsConfigCmd, mbnscSensorsConfigChangedTime, mbnscDASecondCircleDisplay, mbnscDAConfigCmd, mbnscDAConfigChangedTime, mbnscGeneralType, mbnscGeneralName, mbnscGeneralFirmwareNumber, mbnscGeneralFirmwareVer, mbnscGeneralStatus, mbnscGeneralAlarms, mbnscGeneralBootloaderNumber, mbnscGeneralBootloaderVer, mbnscGeneralConfigCmd, mbnscGeneralConfigChangedTime, mbnscSNMPManager1, mbnscSNMPManager2, mbnscSNMPTrapAliveMsgInterval, mbnscSNMPConfigCmd, mbnscSNMPConfigChangedTime, mbnscCommandSWReset, mbnscCommandFactorySetting, mbnscCommandFirmwUpd, mbnscCommandConfigCmd, mbnscTrapAlMsgErrorNr, mbnscTrapAlMsgErrorState, mbnscTrapAlMsgErrorTime } STATUS current DESCRIPTION "All parameters used for DA digital clock" ::= { mbnscMIBGroups 6 } mbnscGrpDK OBJECT-GROUP OBJECTS { mbnscNetGenMAC, mbnscNetGenIPMode, mbnscNetGenIPNameserver, mbnscNetGenTZClientPort, mbnscNetGenConfigPort, mbnscNetGenSnmpMode, mbnscNetGenMulticastMode, mbnscNetGenHostname, mbnscNetGenCommMode, mbnscNetGenMCastGrpIP, mbnscNetGenConfigCmd, mbnscNetGenConfigChangedTime, mbnscNetIPv4Addr, mbnscNetIPv4Mask, mbnscNetIPv4Gateway, mbnscNetIPv4DHCPMode, mbnscNetIPv4ConfigCmd, mbnscNetIPv4ConfigChangedTime, mbnscNetIPv6AddrLocal, mbnscNetIPv6AddrAuto, mbnscNetIPv6AddrDHCP, mbnscNetIPv6AddrFix, mbnscNetIPv6Prefix, mbnscNetIPv6Gateway, mbnscNetIPv6Config, mbnscNetIPv6ConfigCmd, mbnscNetIPv6ConfigChangedTime, mbnscTimeNTP1, mbnscTimeNTP2, mbnscTimeNTP3, mbnscTimeNTP4, mbnscTimeNTPcurrent, mbnscTimeNTPpollIntervall, mbnscTimeDeviceTime, mbnscTimeLocOffset, mbnscTimeLastReception, mbnscTimeConfigCmd, mbnscTimeConfigChangedTime, mbnscTimeZoneVersion, mbnscTimeZoneNumber, mbnscTimeZoneConfigCmd, mbnscTimeZoneConfigChangedTime, mbnscModeDisplayBrightness, mbnscModeDisplayFormat, mbnscModeDisplayAlternate, mbnscModeIRlock, mbnscModeTimeDispZeros, mbnscModeDateDispZeros, mbnscModeTempUnit, mbnscModeClockOpMode, mbnscModeDispDerating, mbnscModeLightCorr, mbnscModeConfigCmd, mbnscModeConfigChangedTime, mbnscSensorsTempActivation, mbnscSensorsTemp1IPAddr, mbnscSensorsTemp2IPAddr, mbnscSensorsConfigCmd, mbnscSensorsConfigChangedTime, mbnscDKFirstLanguage, mbnscDKSecondLanguage, mbnscDKThirdLanguage, mbnscDKTempUnitSecondLang, mbnscDKTempUnitThirdLang, mbnscDKAutoLangSwitchOver, mbnscDKNumOfCharsForWeekday, mbnscDKNamesFormatDisplay, mbnscDKTemp1DescriptEnable, mbnscDKTemp1Description, mbnscDKTemp2DescriptEnable, mbnscDKTemp2Description, mbnscDKWorldTimeZone1, mbnscDKWorldTimeZone1Description, mbnscDKWorldTimeZone2, mbnscDKWorldTimeZone2Description, mbnscDKWorldTimeZone3, mbnscDKWorldTimeZone3Description, mbnscDKWorldTimeZone4, mbnscDKWorldTimeZone4Description, mbnscDKWorldTimeZone5, mbnscDKWorldTimeZone5Description, mbnscDKAutoTimeZoneSwitchOver, mbnscDKConfigCmd, mbnscDKConfigChangedTime, mbnscGeneralType, mbnscGeneralName, mbnscGeneralFirmwareNumber, mbnscGeneralFirmwareVer, mbnscGeneralStatus, mbnscGeneralAlarms, mbnscGeneralBootloaderNumber, mbnscGeneralBootloaderVer, mbnscGeneralConfigCmd, mbnscGeneralConfigChangedTime, mbnscSNMPManager1, mbnscSNMPManager2, mbnscSNMPTrapAliveMsgInterval, mbnscSNMPConfigCmd, mbnscSNMPConfigChangedTime, mbnscCommandSWReset, mbnscCommandFactorySetting, mbnscCommandFirmwUpd, mbnscCommandConfigCmd, mbnscTrapAlMsgErrorNr, mbnscTrapAlMsgErrorState, mbnscTrapAlMsgErrorTime } STATUS current DESCRIPTION "All parameters used for DK digital clock" ::= { mbnscMIBGroups 7 } mbnscGrpNMI OBJECT-GROUP OBJECTS { mbnscNetGenMAC, mbnscNetGenIPMode, mbnscNetGenIPNameserver, mbnscNetGenTZClientPort, mbnscNetGenConfigPort, mbnscNetGenSnmpMode, mbnscNetGenMulticastMode, mbnscNetGenHostname, mbnscNetGenCommMode, mbnscNetGenMCastGrpIP, mbnscNetGenConfigCmd, mbnscNetGenConfigChangedTime, mbnscNetIPv4Addr, mbnscNetIPv4Mask, mbnscNetIPv4Gateway, mbnscNetIPv4DHCPMode, mbnscNetIPv4ConfigCmd, mbnscNetIPv4ConfigChangedTime, mbnscNetIPv6AddrLocal, mbnscNetIPv6AddrAuto, mbnscNetIPv6AddrDHCP, mbnscNetIPv6AddrFix, mbnscNetIPv6Prefix, mbnscNetIPv6Gateway, mbnscNetIPv6Config, mbnscNetIPv6ConfigCmd, mbnscNetIPv6ConfigChangedTime, mbnscTimeNTP1, mbnscTimeNTP2, mbnscTimeNTP3, mbnscTimeNTP4, mbnscTimeNTPcurrent, mbnscTimeNTPpollIntervall, mbnscTimeDeviceTime, mbnscTimeLocOffset, mbnscTimeLastReception, mbnscTimeSyncTo, mbnscTimeConfigCmd, mbnscTimeConfigChangedTime, mbnscTimeZoneVersion, mbnscTimeZoneNumber, mbnscTimeZoneConfigCmd, mbnscTimeZoneConfigChangedTime, mbnscModeConfigCmd, mbnscModeConfigChangedTime, mbnscNMIDCFCurrentLoop, mbnscNMILineDriver, mbnscNMIMOBALineMode, mbnscNMIMOBALineHandMode, mbnscNMIActiveDCFMode, mbnscNMIConfigCmd, mbnscNMIConfigChangedTime, mbnscNMISideClock1, mbnscNMISideClock2, mbnscNMISideClock3, mbnscNMISideClock4, mbnscNMISideClock5, mbnscNMISideClock6, mbnscNMISideClock7, mbnscNMISideClock8, mbnscNMISideClock9, mbnscNMISideClock10, mbnscNMISideClock11, mbnscNMISideClock12, mbnscGeneralType, mbnscGeneralName, mbnscGeneralFirmwareNumber, mbnscGeneralFirmwareVer, mbnscGeneralStatus, mbnscGeneralAlarms, mbnscGeneralConfigCmd, mbnscGeneralConfigChangedTime, mbnscSNMPManager1, mbnscSNMPManager2, mbnscSNMPTrapAliveMsgInterval, mbnscSNMPConfigCmd, mbnscSNMPConfigChangedTime, mbnscCommand12Pos, mbnscCommandSWReset, mbnscCommandConfigCmd, mbnscTrapAlMsgErrorNr, mbnscTrapAlMsgErrorState, mbnscTrapAlMsgErrorTime } STATUS current DESCRIPTION "All parameters used for Network-MOBALine-Interface NMI" ::= { mbnscMIBGroups 8 } mbnscGrpNCC OBJECT-GROUP OBJECTS { mbnscNetGenMAC, mbnscNetGenIPMode, mbnscNetGenIPNameserver, mbnscNetGenTZClientPort, mbnscNetGenConfigPort, mbnscNetGenSnmpMode, mbnscNetGenMulticastMode, mbnscNetGenHostname, mbnscNetGenCommMode, mbnscNetGenMCastGrpIP, mbnscNetGenConfigCmd, mbnscNetGenConfigChangedTime, mbnscNetIPv4Addr, mbnscNetIPv4Mask, mbnscNetIPv4Gateway, mbnscNetIPv4DHCPMode, mbnscNetIPv4ConfigCmd, mbnscNetIPv4ConfigChangedTime, mbnscNetIPv6AddrLocal, mbnscNetIPv6AddrAuto, mbnscNetIPv6AddrDHCP, mbnscNetIPv6AddrFix, mbnscNetIPv6Prefix, mbnscNetIPv6Gateway, mbnscNetIPv6Config, mbnscNetIPv6ConfigCmd, mbnscNetIPv6ConfigChangedTime, mbnscTimeNTP1, mbnscTimeNTP2, mbnscTimeNTP3, mbnscTimeNTP4, mbnscTimeNTPcurrent, mbnscTimeNTPpollIntervall, mbnscTimeDeviceTime, mbnscTimeLocOffset, mbnscTimeLastReception, mbnscTimeSyncTo, mbnscTimeConfigCmd, mbnscTimeConfigChangedTime, mbnscTimeZoneVersion, mbnscTimeZoneNumber, mbnscTimeZoneConfigCmd, mbnscTimeZoneConfigChangedTime, mbnscModeConfigCmd, mbnscModeConfigChangedTime, mbnscNCCLightProperties, mbnscNCCLightBrightness, mbnscNCCMOBALineHandMode, mbnscNCCSideClock1, mbnscNCCSideClock2, mbnscNCCWeekprogID, mbnscNCCConfigCmd, mbnscNCCConfigChangedTime, mbnscGeneralType, mbnscGeneralName, mbnscGeneralFirmwareNumber, mbnscGeneralFirmwareVer, mbnscGeneralStatus, mbnscGeneralAlarms, mbnscGeneralConfigCmd, mbnscGeneralConfigChangedTime, mbnscSNMPManager1, mbnscSNMPManager2, mbnscSNMPTrapAliveMsgInterval, mbnscSNMPConfigCmd, mbnscSNMPConfigChangedTime, mbnscCommand12Pos, mbnscCommandSWReset, mbnscCommandConfigCmd, mbnscTrapAlMsgErrorNr, mbnscTrapAlMsgErrorState, mbnscTrapAlMsgErrorTime } STATUS current DESCRIPTION "All parameters used for Network-Clock-Controller NCC" ::= { mbnscMIBGroups 9 } mbnscGrpNPR OBJECT-GROUP OBJECTS { mbnscNetGenMAC, mbnscNetGenIPMode, mbnscNetGenIPNameserver, mbnscNetGenTZClientPort, mbnscNetGenConfigPort, mbnscNetGenSnmpMode, mbnscNetGenMulticastMode, mbnscNetGenHostname, mbnscNetGenCommMode, mbnscNetGenMCastGrpIP, mbnscNetGenConfigCmd, mbnscNetGenConfigChangedTime, mbnscNetIPv4Addr, mbnscNetIPv4Mask, mbnscNetIPv4Gateway, mbnscNetIPv4DHCPMode, mbnscNetIPv4ConfigCmd, mbnscNetIPv4ConfigChangedTime, mbnscNetIPv6AddrLocal, mbnscNetIPv6AddrAuto, mbnscNetIPv6AddrDHCP, mbnscNetIPv6AddrFix, mbnscNetIPv6Prefix, mbnscNetIPv6Gateway, mbnscNetIPv6Config, mbnscNetIPv6ConfigCmd, mbnscNetIPv6ConfigChangedTime, mbnscTimeNTP1, mbnscTimeNTP2, mbnscTimeNTP3, mbnscTimeNTP4, mbnscTimeNTPcurrent, mbnscTimeNTPpollIntervall, mbnscTimeDeviceTime, mbnscTimeLocOffset, mbnscTimeLastReception, mbnscTimeSyncTo, mbnscTimeConfigCmd, mbnscTimeConfigChangedTime, mbnscTimeZoneVersion, mbnscTimeZoneNumber, mbnscTimeZoneConfigCmd, mbnscTimeZoneConfigChangedTime, mbnscModeConfigCmd, mbnscModeConfigChangedTime, mbnscNPRMode, mbnscNPRWeekprogID, mbnscNPRRelayChannelStatus, mbnscNPRRelayChannelLockStatus, mbnscNPRLockStatus, mbnscNPRChannelNumbers, mbnscNPRSwitchMode, mbnscNPRConfigCmd, mbnscNPRConfigChangedTime, mbnscGeneralType, mbnscGeneralName, mbnscGeneralFirmwareNumber, mbnscGeneralFirmwareVer, mbnscGeneralStatus, mbnscGeneralAlarms, mbnscGeneralConfigCmd, mbnscGeneralConfigChangedTime, mbnscSNMPManager1, mbnscSNMPManager2, mbnscSNMPTrapAliveMsgInterval, mbnscSNMPConfigCmd, mbnscSNMPConfigChangedTime, mbnscCommand12Pos, mbnscCommandSWReset, mbnscCommandConfigCmd, mbnscTrapAlMsgErrorNr, mbnscTrapAlMsgErrorState, mbnscTrapAlMsgErrorTime } STATUS current DESCRIPTION "All parameters used for Network-Programmable-Relay NPR" ::= { mbnscMIBGroups 10 } mbnscGrpTREND OBJECT-GROUP OBJECTS { mbnscNetGenMAC, mbnscNetGenIPMode, mbnscNetGenIPNameserver, mbnscNetGenTZClientPort, mbnscNetGenConfigPort, mbnscNetGenSnmpMode, mbnscNetGenMulticastMode, mbnscNetGenHostname, mbnscNetGenCommMode, mbnscNetGenMCastGrpIP, mbnscNetGenConfigCmd, mbnscNetGenConfigChangedTime, mbnscNetIPv4Addr, mbnscNetIPv4Mask, mbnscNetIPv4Gateway, mbnscNetIPv4DHCPMode, mbnscNetIPv4ConfigCmd, mbnscNetIPv4ConfigChangedTime, mbnscNetIPv6AddrLocal, mbnscNetIPv6AddrAuto, mbnscNetIPv6AddrDHCP, mbnscNetIPv6AddrFix, mbnscNetIPv6Prefix, mbnscNetIPv6Gateway, mbnscNetIPv6Config, mbnscNetIPv6ConfigCmd, mbnscNetIPv6ConfigChangedTime, mbnscTimeNTP1, mbnscTimeNTP2, mbnscTimeNTP3, mbnscTimeNTP4, mbnscTimeNTPcurrent, mbnscTimeNTPpollIntervall, mbnscTimeDeviceTime, mbnscTimeLocOffset, mbnscTimeLastReception, mbnscTimeSyncTo, mbnscTimeConfigCmd, mbnscTimeConfigChangedTime, mbnscTimeZoneVersion, mbnscTimeZoneNumber, mbnscTimeZoneConfigCmd, mbnscTimeZoneConfigChangedTime, mbnscModeConfigCmd, mbnscModeConfigChangedTime, mbnscGeneralType, mbnscGeneralName, mbnscGeneralFirmwareNumber, mbnscGeneralFirmwareVer, mbnscGeneralStatus, mbnscGeneralAlarms, mbnscGeneralConfigCmd, mbnscGeneralConfigChangedTime, mbnscSNMPManager1, mbnscSNMPManager2, mbnscSNMPTrapAliveMsgInterval, mbnscSNMPConfigCmd, mbnscSNMPConfigChangedTime, mbnscCommand12Pos, mbnscCommandSWReset, mbnscCommandConfigCmd, mbnscTrapAlMsgErrorNr, mbnscTrapAlMsgErrorState, mbnscTrapAlMsgErrorTime } STATUS current DESCRIPTION "All parameters used for TREND movement" ::= { mbnscMIBGroups 11 } mbnscGrpNotUsedParameters OBJECT-GROUP OBJECTS { mbnscTimeZoneEntry1, mbnscTimeZoneEntry2, mbnscTimeZoneEntry3, mbnscTimeZoneEntry4, mbnscTimeZoneEntry5, mbnscTimeZoneEntry6, mbnscTimeZoneEntry7, mbnscModeSwitchInfo, mbnscCommandExtContact } STATUS current DESCRIPTION "All parameters not used in other groups" ::= { mbnscMIBGroups 100 } END